(Solved) Load flow study is carried out for A. fault calculations B. stability studies C. system planning D. load frequency control.

-

 Question : 

Load flow study is carried out for... (GETCO 2012)

A. fault calculations

B. stability studies

C. system planning

D. load frequency control


Answer : C


Explanation :

Load flow study is not useful in fault calculations, stability stydies and load frequency control. It is only useful for system planning. 

Decide about which load to turn On and Off for particular time interval can be made by system planning. 

Please comment below for further queries. Thank you! 


Comments

Post a Comment

Popular posts from this blog

Explain superposition theorem and use the principle of superposition to find the voltage Vo in the circuit

-
Image
Superposition Theorem Requirement: Power System is a complex network having number of voltage and current sources and number of loads. Now to analyze the network we need to find voltage/current at particular branch or load.  In such cases calculations for thevenin's and norton's theorem becomes difficult. We can use superposition theorem to find voltage/current at any branch or load in complex network. In this theorem only one source considered at a time and total voltage/current is sum of voltage/current obtained by considering individual source.   Statement of Superposition Theorem:
Read more

(Solved) An LVDT is connected to an amplifier of gain 250 the output terminals of which are connected to a 5 V voltmeter. The meter's scale can be read to 1/5th of a division and has 100 divisions in all. Given that a core displacement of 0.5 mm provides an output of 2 mV from the LVDT, find, 1. The sensitivity of the LVDT 2. The sensitivity of the whole system 3. The resolution of the instrument in centimeters

-
Image
 Question : An LVDT is connected to an amplifier of gain 250 the output terminals of which are connected to a 5 V voltmeter. The meter's scale can be read to 1/5th of a division and has 100 divisions in all. Given that a core displacement of 0.5 mm provides an output of 2 mV from the LVDT, find,  1. The sensitivity of the LVDT  2. The sensitivity of the whole system  3. The resolution of the instrument in centimeters Explanation : (a) Sensitivity of LVDT = Output voltage /displacement  Sensitivity of LVDT = 2mV/0.5 mm = 4 mV/mm (b)Sensitivity of whole setup = amplification factor*sensitivity of LVDT  Sensitivity of whole setup = 250*(4 mV/mm) = 1000 mV/mm (c) The resolution of the instrument in centimeters = minimum voltage that can be read by instrument /sensitivity of whole setup  There are 100 divisions to measure upto 5V.  So 1 division can read 5/100 = 0.05V Scale can read 1/5 of a division.  So minimum voltage that can be read = 0.05/5 ...
Read more

(Solved) A step down DC chopper has a resistive load of R = 15 ohm and input Vdc = 200 V. When the chopper remain ON, it's voltage drop is 2.5V. The chopper frequency is 1 kHz. If the duty cycle is 50%, determine: a) Average output voltage b) RMS output voltage c) Chopper efficiency d) The effective input resistance of the chopper

-
Image
Question:   A step down DC chopper has a resistive load of R = 15 ohm and input Vdc = 200 V. When the chopper remain ON, it's voltage drop is 2.5V. The chopper frequency is 1 kHz. If the duty cycle is 50%, determine:  a) Average output voltage  b) RMS output voltage  c) Chopper efficiency  d) The effective input resistance of the chopper Answer: We can get answers directly by applying relevant formulas as shown below.  (a) Average output voltage = 98.75 V (b) RMS output voltage = 139.6536 V (c) Chopper efficiency = 98.75% (d) The effective input resistance = 30.3799 ohm Additional information : Waveforms for step down chopper are shown below : For any queries regarding above solution please comment below. Thank you! 
Read more